Digital Still Camera
Instruction Manual
DSC-T70/T75/T200
GB
For details on advanced operations, please read “Cyber-
shot Handbook” (PDF) and “Cyber-shot Step-up Guide”
on the CD-ROM (supplied) using a computer.
Operating Instructions
Before operating the unit, please read this manual thoroughly, and retain it for future reference.
© 2007 Sony Corporation
3-219-483-12(1)
long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system.
This will prevent damage to the set due to
lightning and power-line surges.
[ Cleaning
Unplug the set from the wall outlet before
cleaning or polishing it. Do not use liquid cleaners
or aerosol cleaners. Use a cloth lightly dampened
with water for cleaning the exterior of the set.
Service
Installation
[ Damage Requiring Service
Unplug the set from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
– When the power cord or plug is damaged or
frayed.
[ Water and Moisture
Do not use power-line operated sets near water –
for example, near a bathtub, washbowl, kitchen
sink, or laundry tub, in a wet basement, or near a
swimming pool, etc.
– If liquid has been spilled or objects have fallen
into the set.
[ Power-Cord Protection
Route the power cord so that it is not likely to be
walked on or pinched by items placed upon or
against them, paying particular attention to the
plugs, receptacles, and the point where the cord
exits from the appliance.
– If the set has been exposed to rain or water.
– If the set has been subject to excessive shock by
being dropped, or the cabinet has been
damaged.
– If the set does not operate normally when
following the operating instructions. Adjust
only those controls that are specified in the
operating instructions. Improper adjustment of
other controls may result in damage and will
often require extensive work by a qualified
technician to restore the set to normal operation.
[ Accessories
Do not place the set on an unstable cart, stand,
tripod, bracket, or table. The set may fall, causing
serious injury to a child or an adult, and serious
damage to the set. Use only a cart, stand, tripod,
bracket, or table recommended by the
manufacturer.
– When the set exhibits a distinct change in
performance – this indicates a need for service.
[ Ventilation
[ Servicing
Do not attempt to service the set yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards.
The slots and openings in the cabinet are provided
for necessary ventilation. To ensure reliable
operation of the set, and to protect it from
overheating, these slots and openings must never
be blocked or covered.
Refer all servicing to qualified service personnel.
– Never cover the slots and openings with a cloth
or other materials.
– Never block the slots and openings by placing
the set on a bed, sofa, rug, or other similar
surface.
– Never place the set in a confined space, such as
a bookcase, or built-in cabinet, unless proper
ventilation is provided.
[ Replacement parts
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer that have the same
characteristics as the original parts.
Unauthorized substitutions may result in fire,
electric shock, or other hazards.
– Do not place the set near or over a radiator or
heat register, or where it is exposed to direct
sunlight.
[ Safety Check
Upon completion of any service or repairs to the
set, ask the service technician to perform routine
safety checks (as specified by the manufacturer)
to determine that the set is in safe operating
condition.
[ Lightning
For added protection for this set during a lightning
storm, or when it is left unattended and unused for
3
Read this first
CAUTION
For Customers in the U.S.A.
Replace the battery with the specified type only.
Otherwise, fire or injury may result.
If you have any questions about this product, you
may call:
Sony Customer Information Center
1-800-222-SONY (7669)
The number below is for the FCC related matters
only.
Do not expose the batteries to excessive heat such
as sunshine, fire or the like.
For Customers in the U.S.A. and
Canada
[ Regulatory Information
Declaration of Conformity
Trade Name: SONY
Model No.: DSC-T200
Responsible Party: Sony Electronics Inc.
Address: 16530 Via Esprillo,
San Diego, CA 92127U.S.A.
[ RECYCLING LITHIUM-ION
BATTERIES
Lithium-Ion batteries are
recyclable.
You can help preserve our
environment by returning your
used rechargeable batteries to
the collection and recycling
location nearest you.
Telephone No.: 858-942-2230
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
For more information regarding recycling of
rechargeable batteries, call toll free
Caution: Do not handle damaged or leaking
Lithium-Ion batteries.
Declaration of Conformity
Trade Name: SONY
Model No.: DSC-T70, DSC-T75
Responsible Party: Sony Electronics Inc.
Address: 16530 Via Esprillo,
San Diego, CA 92127U.S.A.
Telephone No.: 858-942-2230
[ HD Output Adaptor Cable
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
This Class B digital apparatus complies with
Canadian ICES-003.
Battery charger
This power unit is intended to be correctly
orientated in a vertical or floor mount position.
4
[ CAUTION
For Customers in Europe
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate this
equipment.
This product has been tested and found compliant
with the limits set out in the EMC Directive for
using connection cables shorter than 3 meters
(9.8 feet).
[ Note:
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
[ Attention
The electromagnetic fields at the specific
frequencies may influence the picture and sound
of this unit.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
[ Notice
If static electricity or electromagnetism causes
data transfer to discontinue midway (fail), restart
the application or disconnect and connect the
communication cable (USB, etc.) again.
[ Disposal of Old Electrical &
Electronic Equipment (Applicable
in the European Union and other
European countries with separate
collection systems)
– Reorient or relocate the receiving antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
This symbol on the product or on its packaging
indicates that this product shall not be treated as
household waste. Instead it shall be handed over
to the applicable collection point for the recycling
of electrical and electronic equipment. By
The supplied interface cable must be used with the
equipment in order to comply with the limits for a
digital device pursuant to Subpart B of Part 15 of
FCC Rules.
ensuring this product is disposed of correctly, you
will help prevent potential negative consequences
for the environment and human health, which
could otherwise be caused by inappropriate waste
handling of this product. The recycling of
For the State of California, USA
only
materials will help to conserve natural resources.
For more detailed information about recycling of
this product, please contact your local Civic
Office, your household waste disposal service or
the shop where you purchased the product.
Perchlorate Material - special handling may
apply, See
Perchlorate Material: Lithium battery contains
perchlorate.
5
Disposal of waste batteries
[ Notice for the customers in the
(applicable in the European Union
and other European countries with
separate collection systems)
countries applying EU Directives
The manufacturer of this product is Sony
Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-
0075 Japan. The Authorized Representative for
EMC and product safety is Sony Deutschland
GmbH, Hedelfinger Strasse 61, 70327 Stuttgart,
Germany. For any service or guarantee matters
please refer to the addresses given in separate
service or guarantee documents.
This symbol on the battery or on the packaging
indicates that the battery provided with this
product shall not be treated as household waste.
By ensuring these batteries are disposed of
correctly, you will help prevent potentially
negative consequences for the environment and
human health which could otherwise be caused by
inappropriate waste handling of the battery. The
recycling of the materials will help to conserve
natural resources.
In case of products that for safety, performance or
data integrity reasons require a permanent
connection with an incorporated battery, this
battery should be replaced by qualified service
staff only.
To ensure that the battery will be treated properly,
hand over the product at end-of-life to the
applicable collection point for the recycling of
electrical and electronic equipment.
Notice for customers in the
United Kingdom
A moulded plug complying with BS 1363 is fitted
to this equipment for your safety and
convenience.
Should the fuse in the plug supplied need to be
replaced, a fuse of the same rating as the supplied
one and approved by ASTA or BSI to BS 1362,
(i.e., marked with an
used.
or
mark) must be
If the plug supplied with this equipment has a
detachable fuse cover, be sure to attach the fuse
cover after you change the fuse. Never use the
plug without the fuse cover. If you should lose the
fuse cover, please contact your nearest Sony
service station.
For all other batteries, please view the section on
how to remove the battery from the product
safely. Hand the battery over to the applicable
collection point for the recycling of waste
batteries.
For more detailed information about recycling of
this product or battery, please contact your local
Civic Office, your household waste disposal
service or the shop where you purchased the
product.
6
Table of contents
Learning the various functions – HOME/Menu ........................... 22
Using the HOME screen ......................................................................... 22
Menu items.............................................................................................. 25
Supported Operating Systems for USB connection and application
Viewing images ...................................................................................... 35
7
Notes on using your camera
[ Internal memory and “Memory
[ Notes on the LCD screen
Stick Duo” back up
• The LCD screen is manufactured using
extremely high-precision technology so over
99.99% of the pixels are operational for
effective use. However, there may be some tiny
black points and/or bright points (white, red,
blue or green in color) that constantly appear on
the LCD screen. These points are normal in the
manufacturing process and do not affect the
recording in any way.
• If water droplets or other liquids splash on the
LCD screen and make it wet, immediately wipe
off the screen with a soft cloth. Leaving liquids
on the LCD screen surface can harm the quality
and cause a malfunction.
Do not turn off the camera or remove the battery
pack or “Memory Stick Duo” while the access
lamp is lighted, as the internal memory data or
“Memory Stick Duo” data may be destroyed.
Always protect your data by making a back up
copy.
[ Notes on recording/playback
• Before you start recording, make a trial
recording to make sure that the camera is
working correctly.
• This camera is neither dust-proof, nor splash-
proof, nor water-proof. Read “Precautions”
(page 36) before operating the camera.
• Be careful not to get the camera wet. Water
entering the inside of the camera may cause
malfunctions which in some cases may not be
repairable.
• Do not aim the camera at the sun or other bright
light. It may cause the malfunction of your
camera.
• Do not use the camera near a location that
generates strong radio waves or emits radiation.
The camera may not be able to record or play
back properly.
• Using the camera in sandy or dusty locations
may cause malfunctions.
• If moisture condensation occurs, remove it
[ On image data compatibility
• This camera conforms with DCF (Design rule
for Camera File system) universal standard
established by JEITA (Japan Electronics and
Information Technology Industries
Association).
• Playback of images recorded with your camera
on other equipment and playback of images
recorded or edited with other equipment on your
camera are not guaranteed.
[ Warning on copyright
Television programs, films, videotapes, and other
materials may be copyrighted. Unauthorized
recording of such materials may be contrary to the
provisions of the copyright laws.
• Do not shake or strike the camera. In addition to
malfunctions and an inability to record images,
this may render the recording medium unusable,
or cause image data breakdown, damage or loss.
[ No compensation for contents of
the recording
The contents of the recording cannot be
compensated for if recording or playback is not
possible due to a malfunction of your camera or
recording media, etc.
• Clean the flash surface before use. The heat of
flash emission may cause dirt on the flash
surface to become discolored or to stick to the
flash surface, resulting in insufficient light
emission.
[ On illustrations
Illustrations used in this manual are of DSC-T200
unless noted otherwise.
8
Getting started
Checking the accessories supplied
• Battery charger BC-CSD (1)
• Adaptor plate (1)
You can place the camera on the Cyber-shot
Station (not supplied) using the adaptor plate.
• Power cord (mains lead) (1)
(not supplied in the USA and Canada)
• USB, A/V cable for multi-use terminal (1)
• HD Output Adaptor Cable (1) (DSC-T75 only)
• Rechargeable battery pack NP-BD1 (1)/
Battery case (1)
• Paint pen (1)
• Wrist strap (1)
• CD-ROM (Cyber-shot application software/
“Cyber-shot Handbook”/“Cyber-shot Step-up
Guide”) (1)
• Instruction Manual (this manual) (1)
About the paint pen
• You can paint or put stamps on still images with
the paint pen.
• Attach the paint pen to the wrist strap (shown
right).
• Do not carry the camera by holding the paint
pen. The camera may fall off.
About the wrist strap
DSC-T70/T75
DSC-T200
Attach the strap and place your hand
through the loop to prevent the camera from
damage by being dropped.
Hook
Hook
9
1 Preparing the battery pack
For customers in the USA and
Canada
For customers in countries/regions other than the
USA and Canada
Plug
to the wall outlet
to the wall
outlet
CHARGE lamp
CHARGE lamp
Power cord (mains lead)
1Insert the battery pack into the battery charger.
2Connect the battery charger to the wall outlet (wall socket).
The CHARGE lamp lights up, and charging starts.
When the CHARGE lamp turns off, charging is finished (Practical charge).
If you continue charging the battery pack for about one more hour (until it is fully charged), the charge
will last slightly longer.
[ Charging time
Full charge time
Practical charge time
Approx. 220 min.
Approx. 160 min.
• Time required to charge a fully depleted battery pack at a temperature of 25°C (77°F). Charging may take
longer under certain circumstances or conditions.
• Connect the battery charger to the nearest wall outlet (wall socket) close by.
• Even if the CHARGE lamp is not lit, the battery charger is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet (wall socket). If some trouble occurs while using the
battery charger, immediately shut off the power by disconnecting the plug from the wall outlet (wall
socket).
• When charging is finished, disconnect the power cord (mains lead) from the wall outlet (wall socket), and
remove the battery pack from the battery charger.
• Designed for use with compatible Sony batteries.
10
2 Inserting the battery pack/a “Memory Stick Duo” (not
supplied)
Battery/
“Memory Stick
Duo” cover
Insert the “Memory Stick
Duo” with the terminal side
facing the lens.
Battery
eject lever
Open
Close
Align the v mark of the battery slot with
the v mark on the side of the battery
pack. Press and hold the battery eject
lever and insert the battery pack.
1Open the battery/“Memory Stick Duo” cover.
2Insert the “Memory Stick Duo” (not supplied) all the way in until it clicks.
3Insert the battery pack.
4Close the battery/“Memory Stick Duo” cover.
[ When there is no “Memory Stick Duo” inserted
The camera records/plays back images using the internal memory (approx. 31 MB).
11
[ To check the remaining battery charge
Press POWER button to turn on and check the remaining battery on the LCD screen.
Battery
remaining
indicator
Battery
remaining
guidelines
Sufficient
power
remaining
Battery
almostfully full
charged
Batteryhalf Battery low, Change the battery
recording/
playback
will stop
soon.
with fully charged
one, or charge the
battery. (The warning
indicator flashes.)
• If the NP-FD1 battery pack (not supplied) is used, the minute display (
the battery remaining indicator.
60 Min) is also shown after
• It takes about one minute until the correct battery remaining indicator appears.
• The displayed battery remaining indicator may not be correct under certain circumstances.
[ To remove the battery pack/“Memory Stick Duo”
Open the battery/“Memory Stick Duo” cover.
“Memory Stick Duo”
Battery pack
Make sure that the access lamp is not lit,
then push the “Memory Stick Duo” in once.
Slide the battery eject lever.
Be sure not to drop the battery pack.
• Never remove the battery pack/“Memory Stick Duo” when the access lamp is lit. This may cause damage
to data in the “Memory Stick Duo”/internal memory.
• Use the NP-BD1 battery pack (supplied) only with this camera.
12
3 Turning the camera on/setting the clock
POWER button
Lens
Lens cover
Touch panel
1Press the POWER button or slide the lens cover downward.
2Set the clock by touching the button on the touch panel.
1 Touch the desired date display format, then touch [t].
2 Touch each item, then set its numeric value by touching v/V.
3 Touch [OK].
On the touch panel buttons
Perform settings on this camera by lightly touching the
buttons or icons on the screen with your finger.
• When the item you want to set is not on the screen, touch v/V to
change the page.
• You can return to the previous screen by touching [BACK].
• Touching [?] displays the guide about the touched item. To hide
this guide, touch [?] again.
• When you touch the top right of the screen while shooting, the
icons will momentarily disappear. Taking your finger off the
screen will make the icons reappear.
13
[ To set the date and time again
Touch [HOME], then touch
[ When you turn on the power
• Once the battery is inserted in the camera, it may take time before operation becomes possible.
• If the camera is running on battery power and you do not operate the camera for about three minutes, the
camera turns off automatically to prevent wearing down the battery pack (Auto power-off function).
14
Shooting images easily (Auto Adjustment mode)
Zoom (W/T) lever
Shutter button
Self-timer lamp
Microphone
Flash
DSC-T70/T75
Lens cover
Tripod receptacle (bottom)
Microphone
1Open the lens cover.
2Hold the camera steady, keeping your arm at your side.
Position the subject in
the center of the focus
frame or touch the point
for focusing.
•
is displayed if a face is detected in the touched position or
other than a person’s face is detected.
is displayed if an object
3Shoot with the shutter button.
When shooting still images:
1 Press and hold the shutter button
halfway down to focus.
The z (AE/AF lock) indicator (green)
flashes, a beep sounds, the indicator stops
flashing and remains lit.
2 Press the shutter button fully down.
AE/AF lock indicator
When shooting movies:
Touch [HOME], then touch
(Shooting) t [
Movie Mode] (page 22).
(Movie Mode).
Or, touch the shooting mode setting icon, then touch
Using the zoom:
Slide the zoom (W/T) lever to the T side to zoom and slide to the W side to return.
15
Image size/Self-timer/Shooting mode/Flash/Macro/Display
A Changing the image size
B Using the self-timer
C Changing the shooting mode
D Selecting a flash mode for still images
E Shooting close-up
F Changing the screen display
[ Changing the image size
Touch the image size setting icon on the screen. Touch the desired item, then [BACK].
Still image
For prints up to A3 (11 × 17")
Shoot in 3:2 aspect ratio
For prints up to A4(8.5 × 11")
For prints up to 10 × 15 cm (4 × 6") or 13 × 18 cm(5 × 7")
Shoot at a small image size for e-mail attachment
Shoot in HDTV aspect ratio
Movie
Shoot high quality movie for display on TV
Shoot standard quality movie for display on TV
Shoot at a small image size for e-mail attachments
(Fine)
(Standard)
[ Using the self-timer
Touch the self-timer setting icon on the screen. Touch the desired item, then [BACK].
Self-Timer Off (
): Not using the self-timer
Self-Timer 10sec (
): Setting the 10-second delay self-timer
Self-Timer 2sec ( ): Setting the 2-second delay self-timer
Press the shutter button, the self-timer lamp flashes, and a beep sounds until the shutter
operates.
16
[ Changing the shooting mode
Touch the shooting mode setting icon on the screen. Touch the desired item, then [BACK].
Allows you to shoot still images with the setting adjusted
automatically.
Auto Adjustment
Scene Selection
Program Auto
Allows you to shoot with preset settings according to the scene.
Allows you to shoot with the exposure adjusted automatically (both
the shutter speed and the aperture value). Also you can select various
settings using the menu.
Allows you to record movies with audio.
Movie Mode
Scene Selection
Allows you to shoot images without a flash under low light
conditions.
High Sensitivity
Smile Shutter
When the shutter button is pressed all the way down and the camera
detects a smile, the shutter is released automatically to shoot the
image. Holding down the shutter button again or shooting 6 images
exits the capturing smile screen.
Allows you to shoot soft images for portraits.
Soft Snap
Allows you to shoot sharp images of people in dark places without
losing the dark atmosphere of the surroundings.
Twilight Portrait
Allows you to shoot images without losing the dark atmosphere of
the surroundings.
Twilight
Focuses only on a distant subject to shoot landscapes, etc.
Allows you to shoot moving subjects in bright places.
Landscape
Hi-Speed Shutter
Beach
When shooting seaside or lakeside scenes, the blue of the water is
clearly recorded.
Allows you to shoot bright images of snowy scenes.
Allows you to record fireworks in all their splendor.
Snow
Fireworks
17
[ Flash (Selecting a flash mode for still images)
Touch the flash mode setting icon on the screen. Touch the desired item, then [BACK].
Flash Auto (
):
Strobes when there is insufficient light or backlight (default setting)
Flash On (
)
Slow Synchro (Flash forced on) (
):
The shutter speed is slow in a dark place to clearly shoot the background that is out of flash light.
Flash Off (
)
[ Macro/Close focus (Shooting close-up)
Touch the Macro/Close focus mode setting icon on the screen. Touch the desired item, then
[BACK].
Macro Off (
)
Macro On ( ):
W side
DSC-T200: Approx. 8 cm or farther (3 1/4 inches or farther)
DSC-T70/T75: Approx. 8 cm or farther (3 1/4 inches or farther)
T side
DSC-T200: Approx. 80 cm or farther (31 1/2 inches or farther)
DSC-T70/T75: Approx. 25 cm or farther (9 7/8 inches or farther)
Close focus enabled (
):
Locked to the W side: Approx. 1 to 20 cm (13/32 to 7 7/8 inches)
[ Changing the screen display
Touch [DISP] on the screen to change to the display selection screen.
Display Setup: This sets whether or not to display the icons on the screen.
LCD Brightness: This sets the backlight brightness.
Display Histogram: This sets whether or not to display the histogram on the screen.
18
Viewing/deleting images
(Playback)
button
Zoom (W/T) lever
DSC-T70/T75
Speaker
Multi connector (bottom)
Speaker
1Press
(Playback) button.
(Playback) when the camera is powered off, the camera is turned on automatically and
If you press
set to playback mode. To switch to the shooting mode, press (Playback) again.
2Touch
(previous) /
(next) on the screen to select an image.
Movie:
Touch B to playback a movie.
Fast forward/Rewind: m/M (Touch B or x to return to normal playback.)
Volume control:Touch
Touch
, then adjust the volume with
again. The volume control bar disappears.
/
.
Stop: Touch x.
[
To delete images
1 Display the image you want to delete, then touch
2 Touch [OK].
.
[
To view an enlarged image (playback zoom)
Touch a still image while it is displayed to enlarge the corresponding area. Touch
out.
to zoom
v/V/b/B: Adjusts the position.
[BACK]: Cancels playback zoom.
: Turns v/V/b/B on/off.
• You can also enlarge the image with the zoom (W/T) lever.
19
[
To view an index screen
Touch
Touch
(Index) to display the index screen.
to display the previous/next page.
/
To return to the single image screen, touch the thumbnail image.
• You can also access the index screen by selecting [
screen.
Image Index] in
(View Images) on the HOME
• If you touch [DISP] in index mode, you can set the number of images displayed in the index screen.
[ To delete images in index mode
1 Touch while the index screen is displayed.
2 Touch the thumbnail images to add a check mark to the images you want to delete.
mark is checked in the check box of the image.
To cancel the deletion, touch the image again to deselect the mark.
3 Touch [t], and then touch [OK].
• To delete all the images in a folder, select
(All In This Folder) from (Delete) in the menu screen,
then touch [OK].
[ To play back a series of images (Slideshow)
Touch
.
[ To view images on TV screen
Connect the camera to the TV with the cable for multi-use terminal (supplied).
To audio/video input
jacks
To the multi connector
Cable for multi-use terminal
When viewing on a high definition TV, an HD output adaptor cable (DSC-T75 only) is
required. If you shoot with the image size set to 16:9, the images will be shown in a full-screen
display.
• Movies cannot be played back during HD(1080i) output.
20
Connect the camera to the HDTV with the HD Output Adaptor Cable (DSC-T75 only).
COMPONENT
VIDEO IN
AUDIO
White/Red
To the multi connector
Green/Blue/Red
HD Output Adaptor Cable (DSC-T75 only)
• The cable for video jacks (Green/Blue/Red) is the same color as the respective jacks.
21
Learning the various functions – HOME/Menu
Using the HOME screen
The HOME screen is the gateway screen for all the functions of your camera.
You can access this screen regardless of whether the camera is in shooting mode or playback
mode.
1Touch [HOME] to display the HOME screen.
Item
Category
[HOME]
2Touch the category you want to set.
3Touch the item in the category you want to set.
[ When you select the
(Manage Memory) or
(Settings) category
1 Touch the category you want to change the settings.
2 Touch the desired setting item. Touch v/V to display the other setting items.
3 Touch the setting item that you want to change, and then touch the desired setting value to
set it.
• Touch [×] or [BACK] to return to the previous screen.
22
For details on the operation 1 page 22
HOME items
Touching [HOME] displays the following items. Details on the items are displayed on the
screen by the guide.
Category
Shooting
Items
Auto Adjustment
Scene Selection
Program Auto
Movie Mode
Single Image
Image Index
Slideshow
View Images
Print
Music Tool
Download Music
Memory Tool
Memory Stick Tool
Format
Printing, Other
Manage Memory
Format Music
Create REC. Folder
Change REC. Folder Copy
Internal Memory Tool
Format
Main Settings
Settings
Main Settings 1
Beep
Function Guide
Calibration
Initialize
Housing
Main Settings 2
USB Connect
Video Out
COMPONENT
TV TYPE
Shooting Settings
Shooting Settings 1
AF Illuminator
AF Mode
Grid Line
Digital Zoom
Shooting Settings 2
Auto Orientation
Smile Level
Auto Review
Clock Settings
Language Setting
23
Using the menu items
1Touch [MENU] to display the menu.
Touch [?] to hide
this guide.
[MENU]
• Different items will become visible depending on the selected mode.
2Touch the desired menu item.
• If the desired item is hidden, keep touching v/V until the item appears on the screen.
3Touch the desired setting item.
4Touch [BACK] to turn off the menu.
24
Menu items
The available menu items vary depending on the mode setting (shooting/viewing), and
shooting mode. Only the available items are displayed on the screen.
Menu for shooting
REC Mode
EV
Selects the continuous shooting method.
Adjusts Exposure.
Focus
Changes the focus method.
Metering Mode
White Balance
Color Mode
Flash Level
Red Eye Reduction
Face Detection
SteadyShot
Setup
Selects the metering mode.
Adjusts the color tones.
Changes the vividness of the image or adds special effects.
Adjusts the amount of flash light.
Sets to reduce the red-eye phenomenon.
Detects the faces of your subjects and adjusts focus, etc.
Selects the anti-blur mode.
Selects the shooting settings.
Menu for viewing
(Retouch)
Retouches still images.
(Paint)
Paints on a still image and saves as a new image.
Changes the image size according to usage.
Displays still images in 16:9.
(Multi Resizing)
(Wide Zoom Display)
(Slideshow)
(Delete)
Plays back a series of images.
Deletes images.
(Protect)
Prevents accidental erasure.
Adds a Print order mark on image that you want to print out.
Prints images using a PictBridge compliant printer.
Rotates a still image.
(Print)
(Rotate)
(Select Folder)
(Volume Settings)
Selects the folder for viewing images.
Adjusts the volume.
25
Enjoying your computer
You can display images shot with the camera on the computer. Also, you can use still images
and movies from the camera more than ever by taking advantage of the software. For details,
refer to “Cyber-shot Handbook” on the CD-ROM (supplied).
Supported Operating Systems for USB connection and application
software “Picture Motion Browser” (supplied)
For Windows users
For Macintosh users
USB connection
Windows 2000 Professional SP4,
Windows XP* SP2/Windows
Vista*
Mac OS 9.1/9.2/ Mac OS X (v10.1
to v10.4)
Application software
“Picture Motion
Browser”
Windows 2000 Professional SP4,
Windows XP* SP2/Windows
Vista*
not compatible
* 64-bit editions and Starter (Edition) are not supported.
• Your computer must be pre-installed with an OS listed above. OS upgrades are not supported.
• If your OS does not support USB connections, use a commercially available Memory Stick Reader/Writer.
• For further details on the operating environment of “Picture Motion Browser” Cyber-shot application
software, refer to “Cyber-shot Handbook.”
26
Viewing “Cyber-shot Handbook”
“Cyber-shot Handbook”, which is provided
on the CD-ROM (supplied), describes in
detail how to use the camera. Adobe Reader
is required for viewing the handbook.
[ For Macintosh users
To view the “Cyber-shot Handbook”
1
Turn on your computer, and insert the CD-
ROM (supplied) into the CD-ROM drive.
[ For Windows users
2
3
Select the [Handbook] folder and copy
“Handbook.pdf” stored in the [GB] folder
to your computer.
1
Turn on your computer, and insert the CD-
ROM (supplied) into the CD-ROM drive.
The screen below appears.
After copying is complete, double-click
“Handbook.pdf”.
When you click the [Cyber-shot Handbook]
button, the screen for copying “Cyber-shot
Handbook” appears.
2
3
Follow the on-screen instructions to copy.
When you click the “Cyber-shot Handbook”
button, both of the “Cyber-shot Handbook”
and the “Cyber-shot Step-up Guide” will be
installed.
After the installation is complete, double-
click the shortcut created on the desktop.
27
Indicators on the screen
Touch [DISP] on the screen to change to
Screen operation
You can change the settings by touching the
following: 1, 2, 3.
• Touching an icon displays the guide about
the touched item. To hide this guide,
touch [?] (page 13).
[ When shooting still images
A
Display
Indication
HOME
Displays the HOME screen.
Image size settings
Self-timer settings
Shooting mode settings
Shooting mode (Scene
Selection) settings
• Touch
in the shooting
mode settings to select the
Scene Selection mode.
[ When shooting movies
MENU
Displays the MENU screen.
B
Display
Indication
BACK
Backs to the previous
screen.
This cancels the focusing
on the subject selected by
the touch operation.
Flash mode settings
Macro/Close focus settings
Changes the screen display.
DISP
C
Display
Indication
AF mode/focus preset
settings
• [0.5m] is available in the
DSC-T70/T75 only.
0.5m 1.0m
3.0m 7.0m
Metering mode settings
ISO number settings
0EV
Exposure Value settings
28
Screen indicators
Display
Indication
Screen indicators 4 to 7 show the
current setting status.
Color mode
D
Display
Indication
F
Battery remaining
Display
Indication
Smile shutter (number of
still images)
5
AF range finder frame
Zoom scaling
Low battery warning
Histogram
Flash charging
C:32:00
Self-diagnosis display
E
Display
Indication
G
SteadyShot
Display
Indication
Recording Media
(“Memory Stick Duo”,
internal memory)
z
AE/AF lock
NR slow shutter
Shutter speed
Aperture value
ISO number
125
Recording folder
AF illuminator
Vibration warning
Self-timer
F3.5
ISO400
+2.0EV
Exposure Value
Macro/Close focus
• When [Display Setup] is set
to [Image Only], the current
settings are displayed.
96
Number of recordable
images
00:00:00
Recordable time (h:m:s)
Red-eye reduction
Flash level
Flash mode
• When [Display Setup] is set
to [Image Only], the current
settings are displayed.
Recording mode
Standby
REC
Standby a movie/Recording
a movie
Face Detection
Touch AF indicator
Housing
0:12
Recording time (m:s)
White balance
29
B
[ When playing back still images
[ When playing back movies
Screen operation
Display
Indication
BACK
Backs to the previous
screen.
Adjusts the volume.
Stop
x
N
Playback
Playback zoom
Turns v/V/b/B on/off.
Displays the previous/next
image.
m M
Fast forward/Rewind
DISP
Changes the screen display.
Screen indicators
Screen indicators 3 to 5 show the
current setting status.
C
Display
Indication
Battery remaining
Image size
Check mark
You can change the settings by touching the
following: 1, 2.
Print order (DPOF) mark
Protect
A
Playback zoom
Self-diagnosis display
Display
Indication
C:32:00
HOME
Displays the HOME screen.
Changes to index mode.
Playbacks the slide show.
Deletes the image.
MENU
Displays the MENU screen.
Selects the playback folder.
Returns to the single image
screen from the index
screen.
30
D
Display
Indication
PictBridge connecting
Playback Media (“Memory
Stick Duo”, internal
memory)
Playback folder
8/8 12/12
Image number/Number of
images recorded in selected
folder
PictBridge connecting
Change folder
Recording folder
E
Display
Indication
Low battery warning
Shutter speed
Aperture value
ISO number
125
F3.5
ISO400
+2.0EV
Exposure Value
Metering mode
Flash
White balance
N
Playback
Playback bar
Counter
0:00:00
101-0012
Folder-file number
2007 1 1
9:30 AM
Recorded date/time of the
playback image
Histogram
•
appears when histogram
display is disabled.
31
Battery life and memory capacity
Battery life and number of images that you can record/view
The tables show the approximate number of
images that you can record/view and the
battery life with the battery pack (supplied)
at full capacity and at an ambient
temperature of 25°C (77°F). The numbers
of images that can be recorded or viewed
take into account changing the “Memory
Stick Duo” as necessary.
[ When viewing still images
Battery life
(min.)
No. of Images
DSC-T200
Approx.
210
Approx.
4200
DSC-T70/T75
Approx.
220
Approx.
4400
Note that the actual numbers may be less
than those indicated in the table depending
on the conditions of use.
• Viewing single images in order at about three
second intervals
[ Notes on the battery
[ When shooting still images
• Battery capacity decreases as you use it more, as
the time passes.
• The number of images that can be recorded/
viewed and the battery life are decreased under
the following conditions:
– The surrounding temperature is low.
– The flash is used frequently.
– The camera has been turned on and off many
times.
– The zoom is used frequently.
– The brightness of LCD Backlight is set to up.
– [AF Mode] is set to [Monitor].
– [SteadyShot] is set to [Continuous].
– The battery power is low.
Battery life
No. of Images
(min.)
DSC-T200
Approx. 125 Approx. 250
DSC-T70/T75 Approx. 135 Approx. 270
• Shooting in the following situations:
– [REC Mode] is set to [Normal].
– [AF Mode] is set to [Single].
– [SteadyShot] is set to [Shooting].
– Shooting once every 30 seconds.
– The zoom is switched alternately between the
W and T ends.
– The flash strobes once every two times.
– The Face Detect function is activated.
– The power turns on and off once every ten
times.
• The measurement method is based on the CIPA
standard.
(CIPA: Camera & Imaging Products
Association)
• The battery life/number of images does not
change, regardless of image size.
32
Number of still images and recording time of movies
The number of still images and the length of time for movies may vary depending on the
shooting conditions.
The number of still images and movie recording times may vary, even if the indicated
capacities are the same as shown below.
[ The approximate number of still images
(Units: Images)
“Memory Stick Duo” formatted with this camera
128 MB 256 MB 512 MB 1 GB 2 GB 4 GB
306 618 1223
Internal
Capacity memory
Approx.
31 MB
8 GB
2457
Size
8M
10
10
40
40
72
72
150
150
3:2
306
390
618
787
1223
1557
2498
23980
3997
2457
3127
5M
13
51
92
191
3M
21
82
148
1428
238
306
626
1262
12120
2020
5017
VGA
16:9
202
33
790
133
2941
490
6013
1002
48160
8027
• The number of images listed is for when [REC Mode] is set to [Normal].
• When the number of remaining shootable images is greater than 9,999, the “>9999” indicator appears.
• When an image was recorded using an earlier Sony model and is played back on the camera, the image
may not appear in the actual image size.
[ The approximate recording time of movies
The table below shows the approximate maximum recording times. These are the total times
for all movie files. Continuous shooting is possible for approximately 10 minutes.
(Units: hour : minute : second)
Internal
“Memory Stick Duo” formatted with this camera
Capacity memory
Approx.
31 MB
128 MB 256 MB 512 MB
1 GB
2 GB
4 GB
8 GB
Size
640(Fine)
–
–
0:02:50 0:06:00 0:12:30 0:25:10 0:49:50 1:40:20
640(Standard) 0:01:30 0:05:50 0:10:40 0:22:00 0:45:00 1:30:50 2:59:50 6:01:10
320 0:06:00 0:23:40 0:42:50 1:28:10 3:00:20 6:03:30 11:59:30 24:04:50
• Movies with the size set to [640(Fine)] can only be recorded on a “Memory Stick PRO Duo”.
• This camera does not support HD recordings or playbacks for movies.
33
Troubleshooting
If you experience trouble with your camera, try the following solutions.
1
Check the items below, and refer to “Cyber-shot Handbook” (PDF).
If a code such as “C/E:ss:ss” appears on the screen, refer to “Cyber-shot
Handbook.”
2
Remove the battery pack, and insert the battery pack again after about
one minute, and turn on the power.
3
4
Consult your Sony dealer or local authorized Sony service facility.
Please understand that you give your consent that the contents of the internal memory, Music
files may be checked when you send your camera to be repaired.
Battery pack and power
The battery pack cannot be inserted.
• Insert the battery pack correctly by pressing and holding the battery eject lever open
Cannot turn on the camera.
• After installing the battery pack into the camera, it may take a little while to get the camera
powered.
• The battery pack is dead. Replace it with a new one.
The power turns off suddenly.
• If you do not operate the camera for about three minutes while the power is on, the camera
turns off automatically to prevent wearing down the battery pack. Turn on the camera again
• The battery pack is dead. Replace it with a new one.
34
The battery remaining indicator is incorrect.
• This phenomenon occurs when you use the camera in an extremely hot or cold location.
• The displayed battery remaining differs from the current one. Fully discharge and then charge
the battery pack to correct the display.
• The battery pack is dead. Replace it with a new one.
The battery cannot be charged while inside the camera.
• Use the battery charger (supplied) to charge the battery.
Shooting still images/movies
Cannot record images.
do one of the following:
– Change the “Memory Stick Duo”.
• You cannot record images while charging the flash.
• When shooting a still image, set the shooting mode other than
• Set the shooting mode to when shooting movies.
.
• The image size is set to [640(Fine)] when recording movies. Do one of the following:
– Set the image size to other than [640(Fine)].
– Insert a “Memory Stick PRO Duo.”
Cannot insert dates on images.
• This camera does not have a feature for superimposing dates on images. By using “Picture
Motion Browser,” you can print or save images with the date.
Vertical streaks appear when you are shooting a very bright subject.
• The smear phenomenon is occurring and white, black, red, purple or other streaks appear on
the image. This phenomenon is not a malfunction.
Viewing images
Cannot play back images.
• Press
• The folder/file name has been changed on your computer.
• When an image file has been processed by a computer or when the image file was recorded
using a model other than that of your camera, playback on your camera is not guaranteed.
• The camera is in USB mode. Delete the USB connection.
35
Precautions
[ Do not use/store the camera in
the following places
[ On operating temperatures
Your camera is designed for use under the
temperatures between 0°C and 40°C (32°F and
104°F). Shooting in extremely cold or hot places
that exceed this range is not recommended.
• In an extremely hot, cold or humid place
In places such as in a car parked in the sun, the
camera body may become deformed and this
may cause a malfunction.
[ On moisture condensation
• Under direct sunlight or near a heater
If the camera is brought directly from a cold to a
warm location, moisture may condense inside or
outside the camera. Note that if you shoot with
moisture remaining inside the lens, images will
not be clear.
The camera body may become discolored or
deformed, and this may cause a malfunction.
• In a location subject to rocking vibration
• Near strong magnetic place
• In sandy or dusty places
If moisture condensation occurs
Be careful not to let sand or dust get into the
camera. This may cause the camera to
malfunction, and in some cases this malfunction
cannot be repaired.
Turn off the camera and wait about an hour for the
moisture to evaporate. Note that if you attempt to
shoot with moisture remaining inside the lens, you
will be unable to record clear images.
[ On carrying
[ On the internal rechargeable
Do not sit down in a chair or other place with the
camera in the back pocket of your trousers or
skirt, as this may cause malfunction or damage the
camera.
backup battery
This camera has an internal rechargeable battery
for maintaining the date and time and other
settings regardless of whether the power is on or
off.
This rechargeable battery is continually charged
as long as you are using the camera. However, if
you use the camera for only short periods, it
discharges gradually, and if you do not use the
camera at all for about one month it becomes
completely discharged. In this case, be sure to
charge this rechargeable battery before using the
camera.
However, even if this rechargeable battery is not
charged, you can still use the camera, but the date
and time will not be indicated.
Charging method of the internal
rechargeable backup battery
[ On cleaning
Cleaning the LCD screen
Wipe the screen surface with an LCD cleaning kit
(not supplied) to remove fingerprints, dust, etc.
Cleaning the lens
Wipe the lens with a soft cloth to remove
fingerprints, dust, etc.
Cleaning the camera surface
Clean the camera surface with a soft cloth slightly
moistened with water, then wipe the surface with
a dry cloth. To prevent damage to the finish or
casing:
• Do not expose the camera to chemical products
such as thinner, benzine, alcohol, disposable
cloths, insect repellent, sunscreen or insecticide.
Insert charged battery pack in the camera, and
then leave the camera for 24 hours or more with
the power off.
• Do not touch the camera with any of the above
on your hand.
• Do not leave the camera in contact with rubber
or vinyl for a long time.
36
Specifications
[Power, general]
Camera
Power: Rechargeable battery pack NP-BD1, 3.6 V
[System]
NP-FD1 (not supplied), 3.6 V
AC-LS5K AC Adaptor (not supplied), 4.2 V
Power consumption (during shooting):
Image device: 7.18 mm (1/2.5 type) color CCD,
Primary color filter
Total pixel number of camera:
Approx. 8 286 000 pixels
Effective pixel number of camera:
Approx. 8 083 000 pixels
DSC-T200
1.0 W
DSC-T70/T75
1.0 W
Lens:
Operating temperature: 0 to 40°C (32 to 104°F)
Storage temperature: –20 to +60°C (–4 to +140°F)
Dimensions:
DSC-T200
Carl Zeiss Vario-Tessar 5× zoom lens
f = 5.8 – 29.0 mm (35 – 175 mm when
converted to a 35 mm still camera)F3.5 – 4.4
DSC-T70/T75
Carl Zeiss Vario-Tessar 3× zoom lens
f = 6.33 – 19.0 mm (38 – 114 mm when
converted to a 35 mm still camera)F3.5 – 4.3
DSC-T200
93.5 × 59.3 × 20.4 mm (3 3/4 × 2 3/8 ×
13/16 inches) (W/H/D, excluding protrusions)
DSC-T70/T75
90.0 × 56.4 × 20.7 mm (3 5/8 × 2 1/4 ×
27/32 inches) (W/H/D, excluding protrusions)
Exposure control: Automatic exposure, Scene
Selection (10 modes)
White balance: Automatic, Daylight, Cloudy,
Fluorescent 1,2,3, Incandescent, Flash
Mass (including NP-BD1 battery pack, paint pen
and strap etc.):
DSC-T200
Approx. 186 g (6.6 oz)
DSC-T70/T75
Approx. 156 g (5.5 oz)
File format (DCF compliant):
Still images: Exif Ver. 2.21 JPEG compliant,
DPOF compatible
Movies: MPEG1 compliant (Monaural)
Microphone: Monaural
Speaker: Monaural
Exif Print: Compatible
PRINT Image Matching III: Compatible
PictBridge: Compatible
Recording media: Internal Memory
(approx. 31 MB), “Memory Stick Duo”
Flash: Flash range (ISO sensitivity
(Recommended exposure Index) set to Auto):
DSC-T200
BC-CSD battery charger
Power requirements: AC 100 V to 240 V,
50/60 Hz, 2.2 W
Output voltage: DC 4.2 V, 0.33 A
Operating temperature: 0 to 40°C (32 to 104°F)
Approx. 0.1 to 3.7 m (4 inches to 12 feet
1 3/4 inches) (W)/approx. 0.8 to 2.9 m (2 feet
7 1/2 inches to 9 feet 6 1/4 inches) (T)
DSC-T70/T75
Approx. 0.1 to 3.0 m (4 inches to 9 feet
10 1/8 inches) (W)/approx. 0.25 to 2.5 m
(9 7/8 inches to 8 feet 2 1/2 inches) (T)
Storage temperature: –20 to +60°C (–4 to
+140°F)
[Input and Output connectors]
Multi connector: Video output
Audio output (Monaural)
USB communication
Dimensions: Approx. 62 × 24 × 91 mm (2 1/2 ×
31/32 × 3 5/8 inches) (W/H/D)
Mass: Approx. 75 g (2.7 oz)
USB communication: Hi-Speed USB (USB 2.0
compliant)
[LCD screen]
LCD panel:
DSC-T200
Wide (16:9), 8.8 cm (3.5 type) TFT drive
DSC-T70/T75
Wide (16:9), 7.5 cm (3.0 type) TFT drive
Total number of dots: 230 400 (960 × 240) dots
37
Rechargeable battery pack
NP-BD1
Used battery: Lithium-ion battery
Maximum voltage: DC 4.2 V
Nominal voltage: DC 3.6 V
Capacity: 2.4 Wh (680 mAh)
Design and specifications are subject to change
without notice.
Trademarks
•
, “Cyber-shot” are trademarks
of Sony Corporation.
• “Memory Stick,”
, “Memory Stick PRO,”
, “Memory Stick Duo,”
, “Memory Stick PRO
, “Memory
Duo,”
Stick PRO-HG Duo,”
, “Memory Stick
Micro,” “MagicGate,” and
are trademarks of Sony Corporation.
• “Info LITHIUM” is a trademark of Sony
Corporation.
• Microsoft, Windows, DirectX and Windows
Vista are either registered trademarks or
trademarks of Microsoft Corporation in the
United States and/or other countries.
• Macintosh, Mac OS, iMac, iBook, PowerBook,
Power Mac and eMac are trademarks or
registered trademarks of Apple Inc.
• Intel, MMX, and Pentium are trademarks or
registered trademarks of Intel Corporation.
• Google is a registered trademark of Google, Inc.
• Adobe, the Adobe logo, and Reader are either
registered trademarks or trademarks of Adobe
Systems Incorporated in the United States and/
or other countries.
• In addition, system and product names used in
this manual are, in general, trademarks or
registered trademarks of their respective
developers or manufacturers. However, the ™
or ® marks are not used in all cases in this
manual.
38
39
Additional information on this product and answers
to frequently asked questions can be found at our
Customer Support Website.
Printed on 70% or more recycled paper using VOC
(Volatile Organic Compound)-free vegetable oil based
ink.
Printed in Japan
|